Lytecaster® Recessed Downlighting 1004SIC
®
Page 1 of 1
5" Aperture 0 Shallow Incandescent Convertible IC/Non-IC Frame-in Kit
1004SICN
(Integral Nail)
Overall Length
1004sic/N: 9"
1004SIC
(Integral Screw)
7
1
Frame-In Kit
Overall Width
1004sic/n: 5 3/4”
13" MIN.
24" MAX.
2
6
Top View
3
5
Reflector Trim
Height
1004sic/n: 5 1/2"
4
Ceiling Opening: 5 3/8" Diameter
5" Aperture: Complete Fixture consists of Reflector Trim & Frame-In Kit. Select each separately.
Frame-In Kit
Reflector Trims — See Individual Reflector Trim Specification Sheets
Open Downlight
Cone
Satin Cone
Baffles
Basic White
Wall Washer
Enclosed Diffuser
1004SIC
1012
1008
1005
1071
1085*
1024*
1004SICN
1012NM
1013
1008NM
1010
1010NM
1005WH
1005NM
1005BNM
1076
1013WH
1013CD
1013NM
1013BKNM
1013CDNM
1013BK
1076WH
*for Non-IC applications only
Feature
Options & Accessories
1. Housing: .032” (#20 ga.) Aluminum. UL listed convertible IC/NON-IC. 2"
vertical adjustment in ceiling. Can be removed for access to junction box and
ceiling plenum. 5 1/2" tall for use in 2" X 6" joist construction and shallow
plenum applications. AirSeal® housing minimizes air leakage to less than 2
CFM at 1.57 PSF (or 75pa), which complies with Model Energy Code (Section
602.3.3) and Washington State Energy Code (Section 502.4) and reduces heat
loss and condensation in ceiling.
AirSeal® Kit:
LAS56
NOTE: Use only if factory installed tape or knockouts are removed from vertical
adjustment slots in housing wall.
Labels
UL (Type IC/NON-IC Convertible, Suitable for Damp Locations)
Complies with Air Leakage Requirements stated in the Model Energy Code and
the Washington State Energy Code.
2. Mounting Frame: .048" (#18 ga.) galvanized steel. Locks into position along
length of mounting bars with locking spring and bendable slot. (3) slots 90°
apart simplify alignment.
3. Junction Box: 2" X 4" X 3 1/2" (22 cu. in.) .032" (#22 ga.) galvanized steel.
UL listed for maximum of 8 (#12 ga.) 1104SIC/N and 6 (#12 ga.) 1004SIC/N
90°C through branch circuit conductors. Integral cable clamps permit
attachment of non-metallic (#12 or #14 ga.) Romex® cable without tools or
additional connectors.
AirSeal® is a registered trademark of Lightolier.
Romex® is a registered trademark of General Cable Industries Inc.
Job Information
Type:
4. Mounting Bars: .059" (#16 ga.) galvanized steel. Bars pivot for easy
attachment and wire-in below ceiling line. Bars extend to accommodate
16" to 24" O.C. joist spacing. Bars can accommodate 9" O.C. joist spacing
after a slight field modification (See Instruction Sheet). 1004SIC features
integral self-tapping phillips screws for secure attachment to wood or metal
construction. The 1004SICN features integral nails for secure attachment to
wood. Both attach to T-bar ceilings without the need of accessories.
5. Socket Housing: Impact extruded aluminum or galvanized steel. Attached
trim retaining spring secures trim to any height on housing wall.
6. Socket: Porcelain medium base; nickel plated screw shell. Pre-wired with
#18 ga. SF1 (300 Volt 200° C) leads to junction box.
Job Name:
Cat. No.:
Lamp(s):
Notes:
7. Thermal Protector: Meets NEC and UL requirements. Located inside
housing.
Lightolier a Genlyte company
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
© 2006 Genlyte Group LLC • I0806
|
Land Pride Tiller RTR1042 User Manual
Lennox Hearth Stove C210 User Manual
LevelOne Network Card FNS 5000 User Manual
LG Electronics Cell Phone C1500 User Manual
Liebert Power Supply GXT2 6000RTL630 User Manual
Lochinvar Swimming Pool Heater CP 991 2071 User Manual
Magnavox Car Stereo System AZ6856 User Manual
Magnavox CRT Television 27TP83 C101 User Manual
Marshall electronic Computer Monitor MLYNX17 User Manual
Masterbuilt Charcoal Grill SSSMPG User Manual